The KLUS PDS4 type aluminum extrusion is a basic half inch square shaped channel, perfect for 8mm and 10mm wide low voltage LED Strip Lights. With a variety of cover and finish options this channel can be used indoors and outdoors to create custom LED lighting fixtures. Choose from non-anodized aluminum, double anodized aluminum, and double anodized black finish. The extra frosted indoor cover provides a clean line of light when used with a densely spaced SMD LED strip light with at least 3 LEDs per inch. Change the beam angle of the LED Strip to 10° using the focus lens for a more condensed light beam or wall wash. Outdoor Covers can achieve an IP67 rating when sealed properly using a silicon adhesive and are recommended in any outdoor or UV exposed environment. This channel is also available in 3M lengths in the silver anodized finish, please call (775) 636-6060 to order.
|Model||PDS4 Aluminum Extrusion|
|Dimensions||39.37"L x 0.63"W x 0.47"H|
|Mounting||VHB Tape, Mounting Clips|
|Available Lengths||1M, 2M, (3M Anodized Only)|
|Available Finishes||Non-Anodized, Anodized, Black-Anodized, White Lacquered|
For B2B or Large Quantity Price Info Click Here
Plastic End Caps for PDS4 Aluminum Extrusion
SKU: EX-KL1-CAP-1 View Product Page
We have a small selection of colored plastic end caps for our .5" deep PDS4 square shaped LED Aluminum Extrusions to give your light profile a clean and finished look. Available in white, black, or silver plastic, this cap will fit both the clear and frosted diffuser styles. The faux metal silver finish does not allow for light transmittance while the plain plastic cap does show light through the plastic This product is sold individually and in single units in order to pair with holed end caps if needed. With proper sealing techniques of your PDS4 extrusions with HS outdoor covers these caps can achieve an IP67 water-resistant rating and can be used in outdoor environments.
(2) Extrusion Mounting Clips for Most KL1 Profiles
SKU: EX-KL1-CLIP-2 View Product Page
A set of 2 clips for mounting a variety of our KL1 type LED Aluminum Channels with 0.44" mounting base. Works with a number of our aluminum channels for mounting to any drillable surface. Comes with 2 clips for a secure mounting solution that is simple to install. See a list of compatible extrusions that can be used with these mounting clips below. A minimum of two clips per 1M channel are recommended for a secure installation.
Plastic End Cap with Post for PDS4 .5" Square Extrusion
SKU: EX-KL1-CAP-1P View Product Page
This product is a plastic end cap for our .5" deep square shaped LED Aluminum Extrusions with a built in electrical conducting pole in order to create custom lamps and hanging fixtures with a clean and finished look. Simply solder your positive connection to one end and your negative connection to the other. This cap will fit both the clear and frosted diffuser styles. This product is sold individually and in single units in order to pair with other end caps if needed. This product is non water-resistant and not meant to be exposed to outdoor elements.
IR Sensor Switch for LED Strip Light Channels, 12VDC 3A
SKU: LC-KL-SENS-1 View Product Page
Combine our LED strip lights and aluminum track assortments with this infrared on / off switch to create custom and functional LED light bars. The infrared technology allows you to wave your hand 1-4" from the sensor to turn your lights on and off as well as dimming control. To function properly the IR sensor must be open and exposed with no plastic cover over top. These sensors fit best with our slimmer KL1 style extrusions but can be used with our deeper extrusions by using a small mounting block for a base. You can either purchase the on/off switch or switch plus dimming capability. This 12 volt strip light controller can control up to 3 amps of 12V Strip light or 36 watts. Create your own custom lighting fixtures with simple on off and dimming control by a wave of the hand. Start making custom linear lighting fixtures for your home or business with control at your fingertips. Comes with 3M double sided VHB mounting tape for a permanent bond to your aluminum extrusion.
Touch Sensor Switch for LED Strip Light Channels, 12VDC 3A
SKU: LC-KL-SENS-2 View Product Page
Combine our LED strip lights and aluminum track assortments with this touch sensor on / off switch to create one of a kind touch activated light bars for any indoor lighting application. The touch spring allows you to touch the cover of your KLUS channel to turn your lights on and off as well as dimming control. This switch needs works best with our slimmer KL1 style extrusions and will need extra base height to work with our KL3 or deeper channels. You can either purchase just the on/off switch or switch plus dimming capability. This 12 volt strip light controller can control up to 3 amps of 12V Strip light or 36 watts. Create your own custom lighting fixtures with simple on off and dimming control with just a touch of the hand. Start making custom linear lighting fixtures for your home or business with control at your fingertips.