SKU: LN-DX-NTR-EC
A silicone end cap for sealing non wired ends of both our RGB and Single Color Top Emitting Round Neon Flex Strips. This end cap is intended only for the Round topped version of the flex strip. Silicone Adhesive is required to maintain IP66 waterproof level. All accessories can be found in products listed below.
Waterproof Neon RGB LED Strip Light, Top Emitting - ETL 24VDC - 197" (5m)
SKU: LN-DX-NEON-RGB-5 View Product Page
Create dot free color changing illumination without the addition of a plastic cover or diffuser using our top emitting RGB neon strip light. A special milky silicon coating is extruded around a high density 24VDC RGB strip light to create brilliant line of light 180° color output without any visible dots or hot spots. Constructed with a double-hollow air layer for good heat dissipation this strip is ideal for accent lighting around rooms, signs, displays and so much more. Six 5050 LEDs per every 1.97" cuttable section this strip outputs an impressive 213 lumens per foot when all colors are on full brightness. Create millions of color varieties with the right 24VDC color controller. Keep in mind that this strip is top emitting and will only bend on a vertical axis. Once the strip is cut it must be soldered to re-connect and then sealed using an outdoor rated silicon adhesive. Double sided tape will not stick to the silicon material of this strip. Each 5 meter roll comes with 15 mounting clips, 15 self-tapping screws, 1 wire lead setup, and one end cap. Requiring 7.3 watts of 24VDC power for each foot, the entire roll of 16.4ft would need 120 watts minimum of 24VDC power to light on full brightness. This product is ETL listed, RoHS and CE approved.
Silicone End Cap with Hole and 4 Wire Lead for Round Top Emitting RGB Neon Flex
SKU: LN-DX-NTR-RGB-ECH View Product Page
A 12" long 22AWG 4 wire solder lead with white PVC jacket and one holed end cap for re connection of our RGB Top Emitting Round Neon Flex Strips. The wire lead must be soldered when cutting and re-connecting our single channel top emitting round neon flex strips. Silicone Adhesive is required to maintain IP66 waterproof level. Wires are cut shorter and pre-tinned on the end intended for soldering. All additional accessories are listed found below.
Warm White LED Neon Round Waterproof Vertical Bend Top Emitting - ETL 24VDC - 197"(5m)
SKU: LN-DX-NE-WWH-RV-5 View Product Page
Each 5 meter roll of our top emitting round shaped 3000K LED Neon Flex strip is IP67 waterproof rated with a UV resistant dual core silicone housing to create bright dot free illumination with no shadows or hot spots. A 180° beam angle illuminates around all exposed sides of the round coating, resembling traditional neon without the harmful voltage or chemicals. The milky coating and design of this special strip light delivers 100% light diffusion with no need for a cover or diffuser. This strip is designed to bend on a vertical axis and can be used to wrap perimeters, down light, up light, landscape, architecture, bars, clubs or anywhere needing a diffused, low voltage, linear light. This strip requires 24 volt DC input and consumes 3.51 watts of power per foot to operate. This product is dimmable by our PWM low voltage dimmers or by our magnitude dimmable power supplies with compatible wall switch. This strip can be cut and re-connected every 1.5" and comes with 1 extra wire lead setup, 1 end cap, and 10 plastic mounting clips. For additional quality and safety measures each roll is ETL listed, RoHS and CE approved.
White LED Neon Round Waterproof Vertical Bend Top Emitting - ETL 24VDC - 197"(5m)
SKU: LN-DX-NE-WH-RV-5 View Product Page
Each 5 meter roll of our top emitting round shaped 6000K LED Neon Flex strip is IP67 waterproof rated with a UV resistant dual core silicone housing to create bright dot free illumination with no shadows or hot spots. A 180° beam angle illuminates around all exposed sides of the round coating, resembling traditional neon without the harmful voltage or chemicals. The milky coating and design of this special strip light delivers 100% light diffusion with no need for a cover or diffuser. This strip is designed to bend on a vertical axis and can be used to wrap perimeters, down light, up light, landscape, architecture, bars, clubs or anywhere needing a diffused, low voltage, linear light. This strip requires 24 volt DC input and consumes 3.51 watts of power per foot to operate. This product is dimmable by our PWM low voltage dimmers or by our magnitude dimmable power supplies with compatible wall switch. This strip can be cut and re-connected every 1.5" and comes with 1 extra wire lead setup, 1 end cap, and 10 plastic mounting clips. For additional quality and safety measures each roll is ETL listed, RoHS and CE approved.
Silicone End Cap with Hole and 2 Wire Lead for Round Top Emitting White Neon Flex
SKU: LN-DX-NTR-WH-ECH View Product Page
A 12" long 22AWG 2 wire solder lead with white PVC jacket and one holed end cap for re connection of White and Warm White Top Emitting Round Neon Flex Strips. The wire lead must be soldered when cutting and re-connecting our single channel top emitting round neon flex strips. Silicone Adhesive is required to maintain IP66 waterproof level. Wires are cut shorter and pre-tinned on the end intended for soldering. All additional accessories are listed found below.
Note: * Indicates a required field
- There are currently no reviews for this product