(6) Plastic Mounting Clips for Drywall Extrusion

SKU: EX-KL-CLIP-21-6     View Product Page
This is a set of 6 plastic mounting clips for securely adhering 1M of LED extrusion to a flush mount dry wall aluminum housing. Simply slide the plastic mounting clips into the bottom of the extrusion, 6 needed to securely fasten 1M of extrusion, and then click the extrusion into the aluminum flush mount for 0.5" drywall. See installation instructions and compatible extrusion by clicking the links below.

Plastic End Cap for LIPOD 1" x 1" Extrusion

SKU: EX-KL3-CAP-3     View Product Page
This product is a plastic end cap for the LIPOD 1" Wide x 1" Deep square shaped LED Aluminum Extrusions to give your extrusion a clean and finished look. Available in plastic finish as well as a silver plastic finish, this cap will fit both the clear and frosted diffuser styles. The faux metal silver finish does not allow for light transmittance while the plain plastic cap does show light through the plastic. This product is sold individually and in single units. With proper sealing techniques of your LIPOD extrusions with HS22 cover these caps can achieve an IP67 water-resistant rating and used in outdoor environments.

(2) Extrusion Plastic Mounting Clips for KL3 1" Wide Profiles

SKU: EX-KL3-CLIP-1-2     View Product Page
A set of 2 clips for mounting our 1" wide LED Aluminum Channels. Use the two mounting clips to secure the aluminum channels to any drillable surface. Comes with 2 clips for a secure mounting solution that is simple to install. See a list of compatible extrusions that can be used with these mounting clips below. A minimum of two clips per 1M channel are recommended for a secure installation.

(2) Adjustable Mounting Clip for Most KL3 1" Wide Profiles

SKU: EX-KL3-CLIP-2-2     View Product Page
A set of 2 angle adjustable KLUS brand REGIP mounting brackets compatible with most of our 1" wide Aluminum Channels. Use the two mounting clips to secure the aluminum channels to any drillable surface. The adjustable plastic clips make it so the user can adjust the beam angle of the custom LED lighting fixture. A removable plastic cover allows for quick installation using screws which are then covered to create a clean and finished look. This product is sold in pairs of 2 mounting clips, 2 clips minimum are recommended per 1M of aluminum channel.

(2) GP Surface Mounting Spring for, PDS ZM, TRIADA and 1" Extrusions

SKU: EX-KL-CLIP-18-2     View Product Page
This is a set of 2 spring loaded mounting clips for surface mounting our PDS ZM, Triada, and 1" wide extrusions to drywall, wood, granite, brick, or any other solid surface. Works with any 1" wide extrusion without wings. To use, simply drill a 5/16" - 3/8" wide hole into a surface at least 3/8" thick and push the spring through. Comes with 2 clips, one for each end of the profile. For a more secure mount multiple mounting springs may be necessary.

90 Degree Connector for Anodized Drywall Extrusions

SKU: EX-KL3-CON-90     View Product Page
The ZM-90 connector from KLUS slides between the the backside side of two Anodized drywall extrusions to secure them at a 90 degree angle. This connector is meant for our Anodized extrusions equipped with small backside mounting grooves: LIPOD, LOKOM, LESTO, LARKO, GIZA, GIP, OPAC, SEKODU, and SEPOD. The 90 degree connectors are attached to the extrusions by sliding them into the grooves and expanding with moderate force using a hex key and included screws. Use these along with our straight 180 degree connectors to make secure connections between your strip light extrusions and create one of a kind custom light fixtures and designs in walls, ceilings, and hanging type fixtures.

180 Degree Connector for Anodized Drywall Extrusions

SKU: EX-KL3-CON-180     View Product Page
The ZM-180 connector from KLUS slides between the the backside side of two Anodized drywall extrusions to secure them in a straight line. This connector is meant for our Anodized extrusions equipped with small backside mounting grooves: LIPOD, LOKOM, LESTO, LARKO, GIZA, GIP, OPAC, SEKODU, and SEPOD. The 180 degree connectors are attached to the extrusions by sliding them into the grooves and expanding with moderate force using a hex key and included screws. Use these along with our 90 degree connectors to make secure connections between your strip light extrusions and create one of a kind custom light fixtures and designs in walls, ceilings, and hanging type fixtures.