SKU: LN-SC-NEOS-CON
Use these 9.5" long solderless connectors for our side emitting mini neon strip lights if you do not want to make a connection by solder. After cutting the neon strip on the designated cut line these connectors easily slide into place to make contact on the conductive pads. Each connector includes one 9.5" side emitting strip light cable connector (18AWG), 1 waterproof silicon tape pad, internal install clip, external install clip, screws for end cap. The connector screws into place and requires a Phillips head screw driver for installation.
Mini Neon Side Emitting Waterproof White LED Strip Light - ETL 24VDC - 197" (5m)
SKU: LN-SC-NEOS-W-5 View Product Page
Each 5 meter roll of high quality mini neon side emitting LED strip light has a long lasting IP67 waterproof rated UV resistant PVC housing to create vibrant dot free illumination for a line of light effect. This strip is designed to bend on a horizontal axis and can be used to create curves, designs, lettering, or any layout that benefits from a side emitting strip light. The milky coating and design of this special strip light delivers 100% light diffusion with no hot spots, similar to the look of a neon tube. Use our mini neon led indoors and outdoors for a variety of lighting projects both functional and decorative. This strip requires 24 volt DC input and consumes 3.81 watts of power per foot, at full brightness. This product is dimmable by our PWM low voltage dimmers or by our magnitude dimmable power supplies with compatible wall switch. This strip can be cut and re-connected every 1.5" and comes with 1 extra wire lead setup, 1 end cap, and 20 metal mounting clips.
Mini Neon Side Emitting Waterproof Warm White LED Strip Light - ETL 24VDC - 197" (5m)
SKU: LN-SC-NEOS-WW-5 View Product Page
Each 5 meter roll of commercial grade mini neon side emitting LED strip light has an IP67 waterproof rated UV resistant and durable PVC housing to create vibrant dot free illumination for a line of light effect. The milky coating and design of this special strip light delivers 100% light diffusion with no hot spots, similar to the look of a neon tube. This strip is designed to bend on a horizontal axis and can be used to create curves, designs, lettering, or any other application where a fully diffused side view strip is needed. Use our mini neon led indoors and outdoors for a variety of lighting projects both functional and decorative. This strip requires 24 volt DC input and consumes 3.81 watts of power per foot, at full brightness. This product is dimmable by our PWM low voltage dimmers or by our magnitude dimmable power supplies with compatible wall switch. This strip can be cut and re-connected every 1.5" and comes with 1 extra wire lead setup, 1 end cap, and 20 plastic mounting clips.
End Cap for Mini Neon Side Emmiting LED Strip Light
SKU: LN-SC-NEOS-CAP View Product Page
This end cap is designed to be used only with our side emitting mini neon strip lights, SKU: LN-SC-NEOS-W-5 or LN-SC-NEOS-WW-5. After cutting your strip light use this end cap with an industrial strength plastic bonding adhesive to close and seal your exposed cuts to water, dust, and moisture.
(10) Mounting Clips for Mini Neon Side Emmiting LED Strip Lights
SKU: LN-SC-NEOS-CLIPS-10 View Product Page
This is a pack of 10 mounting clips for our mini neon side emitting strip lights. Each clip has a screw hole with counter sink for mounting to walls, ceilings, stone or concrete. The side emitting strip bends on a horizontal access so mounting tape does not create as tight of a hold as the mounting clips. Sold in packs of 10, for creation of bends, curves, lettering and designs with a bend radius no more than 3.93" to avoid damage to the strip light.
Note: * Indicates a required field
Works well but misleading
I ordered a number of these thinking that I would be able to use them on either end of the side emitting lights. However, the way it connects only allows you to connect it to the starting end of the lights (because of the polarity). I was intending to cut the lights at various places and reconnect the end of the first section and start of the second section together at the wires that come off of these. I ended up rigging a way to do this, but it isn't technically correct, and def not as SAT as I intended. For now though, all the lights turn on and look good. They really need to make the same kind of connector for the other end of these tho.
Jan 18, 2020 | Nadine
Can connect at both ends
I've used these connectors before with good luck. You can connect on either end you just have to use the opposite wire colors on the end where the polarity does not match.
Apr 22, 2020 | Roger
- Click the arrow or text to reveal answers.
- Customer service representatives.
- Verified purchasers of this product.
