This DMX decoder allows for 24 Channels of LED lights to be controlled via a DMX control signal. With two DC power inputs, one for channels 1-12 and the other for 13-24, this LED decoder can control 12 channels of LED lights of similar or variating voltage inputs. This decoder accepts either XLR-3 type connections or bare wire connections for the DMX signal input and output. There are a total of eight, 3 channel, common anode outputs with screw-down terminal blocks for easy connection to your LED lights. This decoder is able to accept 5-24VDC at 3A per channel (twenty four channels total) for max load of 360W/5V, 864W/12V, or 1728W/24V. You can set the starting address of the DMX decoder via DIP switches located on the back of the unit. Please note that each DMX decoder requires 24 addresses in the DMX universe being used as well as a 5-24VDC driver large enough to power the lighting load. A built in LED light test mode is available with this DMX decoder. Systems with more than two DMX decoders being used require an XLR3 DMX terminator cable on the last DMX decoder in the series.
|Click For Product Data Sheet|
|Click For Installation Guide|
|Click For Dip Switch Settings|
|Click For Demonstration Video|
|Model||24 Channel DMX512 Decoder|
|Dimensions||10.24"L x 4.72"W x 1.57"H|
|DMX Type||DMX 512|
|DC Power||5VDC, 12VDC, 24VDC 3A per Channel Max|
|Watts||5VDC - 360W Max|
12VDC - 864W Max
24VDC - 1728W Max
|Warranty Period||1 Year|
Wireless DMX Transmitter and Receiver
SKU: LC-HK-DMX-WI View Product Page
This product is a wireless DMX Transmitter and Receiver designed to send and receive a DMX control signal wirelessly up to 1,000ft (line of sight). A minimum of two units are needed to operate, one is required to send the DMX signal (transmitter) and an unlimited amount of receivers can be paired to the transmitter within the wireless range. Sixteen group options allow for 16 different DMX signals to be wirelessly transmitted in one area. The wireless 2.4Ghz RF signal uses 126 channels decreasing interference and allowing reliable communication. Each unit has a XLR 3 type male/female connectors for the DMX input and output, a DMX decoder, or DMX fixture with built in driver, is then required to set the DMX address and operate your lighting. Each unit includes a 9VDC power adapter, a minimum of 2 units is required to send and receive a DMX signal.
DMX Signal Cable, XLR3 Male to XLR3 Female - 36"
SKU: LA-EL-DMX-CBL6 View Product Page
This is a DMX signal Cable with a XLR3 female plug on one end and XLR3 male plug on the other with 36" of lead wire in between. This cable will allow you to connect a DMX controller or device that has XLR3 output plugs to our PX24501 or 24 Channel DMX Drivers, or to daisy chain any other DMX LED Drivers with XLR3 connectors.
Signal Terminator for DMX Driver XLR3 Type
SKU: LA-EL-DMX-TM2 View Product Page
This is a DMX signal terminator for DMX Decoder / Drivers that use an XLR3 type connection for DMX Signal to LED Lights. This terminator will allow you to terminate the DMX signal in the last DMX driver of your system. For use with DMX systems using more than two XLR3 DMX drivers.
Signal Terminator for DMX Driver RJ45 Type
SKU: LA-EL-DMX-TM View Product Page
This is a DMX signal Terminator for use with LED DMX Drivers that use an RJ45 jack. Use the signal terminator on the DMX output of the last DMX Driver in daisy chain. This terminator is needed if you have more than 3 DMX Drivers in a series of daisy chained drivers.