This Product Has been Discontinued
This product has been discontinued or is no longer available from the manufacturer, we apologize for any inconvenience. Please browse our similar replacement products found below.
PX24500 RGB LED DMX Driver, 12-24VDC 5A/CH
SKU: LC-OL-DMX-PX View Product Page
The most popular DMX Driver style PX24500, which allows you to connect your RGB LED Lights, LED Lighting, LED Ribbon strips or RGB LED Modules to DMX512 or DMX1990 Lighting controllers. Then by using PWM & DMX, you can change the color and dimming of your RGB LED lights. For 12 to 24VDC systems only. Includes one 6' Cat5 cable with RJ45 jack connectors. 5A per channel with a maximum power of 180W / 12VDC or 360W / 24VDC. For use with 4 pin, 3 loop, common anode style RGB LED and LED Lighting. Can be connected to DMX512 signal using RJ45 connectors and Cat5 cables. Unit has DIP switches on the side to manually change the DMX address of each driver. Each PX24500 Driver uses 3 DMX addresses. RGB LEDs and power supply are connected using screw down style connectors. RoHs, CE approved.
Flicker Free RGB LED DMX Driver, 12-24VDC 6A/CH
SKU: LC-HO-DMX3-FF View Product Page
Our flicker free line of DMX LED drivers are the premier RGB DMX decoder for lighting professionals who require smooth fading and color changing effects with no flicker or noticeable steps. The high PWM frequency of 7.8KHz allows for fluid dimming and color control functions, perfect for HD filming with no visible distortion. Simple screw down connectors make it easy to install your 12-24V DC input and RGB LED output, while the DMX connection is made using standard RJ45 Ethernet jacks. Each decoder has a set of 10 dip switches for setting your DMX address and also for test functions when no DMX signal is present. An impressive 6 amps per channel allows you to control up to 216W of 12VDC RGB LED lighting or 432W of 24VDC RGB LED Lighting. This product is intended only for use with 12-24VDC 4 pin, 3 loop, common anode style RGB LED and LED Lighting. DMX input and outputs require a cat5 cable with RJ45 connectors. This product is RoHS and CE approved.
12 Channel LED DMX Decoder, 12-24VDC 4A/CH
SKU: LC-LT-DMX-12CHA View Product Page
This DMX decoder allows for 48 Amps of LED lights to be controlled via a DMX control signal over 12 channels. Select your dimming refresh rate at 8bit (256 levels) or 16bit (65536 levels) to change the smoothness of your color fades and gradients. With two DC power inputs, one for channels 1-6 and the other for 7-12, this decoder can control 6 channels of LED lights of similar or variating voltage inputs. DMX connections are made using either XLR-3 type connections or RJ45 ethernet connections for the DMX signal input and output. There are a total of four, 3 channel, common anode outputs with screw-down terminal blocks for easy connection and control. This decoder is able to accept 12-24VDC at 4A per channel (twelve channels total) for max load of 576W/12V, or 1152W/24V. You can set the starting address of the DMX decoder via the electronic display. Please note that each DMX decoder requires 12 addresses in the DMX universe being used. A built in LED light test mode is available with this DMX decoder, CE, RoHS approved. A 12-24VDC low voltage driver is required to power this unit and must be suffice to power the load of the light output. Systems with more than two DMX decoders being used require an XLR3 or RJ45 DMX terminator on the last DMX decoder in the series.
24 Channel LED DMX Decoder, 5-24VDC 3A/CH
SKU: LC-EU-DMX-PX243 View Product Page
This DMX decoder allows for 24 Channels of LED lights to be controlled via a DMX control signal. With two DC power inputs, one for channels 1-12 and the other for 13-24, this LED decoder can control 12 channels of LED lights of similar or variating voltage inputs. This decoder accepts either XLR-3 type connections or bare wire connections for the DMX signal input and output. There are a total of eight, 3 channel, common anode outputs with screw-down terminal blocks for easy connection to your LED lights. This decoder is able to accept 5-24VDC at 3A per channel (twenty four channels total) for max load of 360W/5V, 864W/12V, or 1728W/24V. You can set the starting address of the DMX decoder via DIP switches located on the back of the unit. Please note that each DMX decoder requires 24 addresses in the DMX universe being used as well as a 5-24VDC driver large enough to power the lighting load. A built in LED light test mode is available with this DMX decoder. Systems with more than two DMX decoders being used require an XLR3 DMX terminator cable on the last DMX decoder in the series.